[ Chinese wardrobe net ] Customized wardrobe can determine the size, material and style of the wardrobe according to your own needs, to meet the various needs of everyone. So everyone knows how to install a custom closet? The following website will tell you the details of the custom closet installation and the custom wardrobe installation.
Custom wardrobe installation details:
1. Check the work before installation, find the abnormality, and feedback in the first time to make corrections in time.
2. Carefully check the matching of the drawing identification with the site to determine the installation sequence.
3. Pay attention to the protection of the product assembly during the installation process.
4. Beam position, top line, and cut-off angle of the closing plate should be carefully checked and cut accurately.
5. Note that the hole surface of the side panel of the No. 4 cabinet should not be placed in the No. 4 cabinet.
6. When the nail backing plate is used, the diagonal of the measuring cabinet should be equal. If the solid layer is uneven, it should be flattened with a planing knife to nail the backing plate.
7. If the customer asks a question during the installation, it should be answered in time and the rationality of the disposal method should be informed.
8. If there is a problem with the installation, the installation worker must return to the installation note and return to the repair order to complete the tracking service.
9. After installation, you must first self-check, adjust, and then the customer acceptance, signature confirmation.
10. The entire installation service process must be completed after the customer has a clean environment.
11. If the cloakroom is high, install it from the inside out.
12. There is a top cabinet, the inside of the first cabinet, the lower cabinet and the upper cabinet are installed at the same time and then the lower cabinet is installed.
13. Adopt the vertical loading method, first and then the outside, from left to right and from right to left, the side panels are first connected to the main line, and the bottom line is fixed by the corner code. After the board, people have to climb out from the top cabinet. If the space in the top cabinet is too small, you can saw the back panel behind the drawer and then fix the back panel with the corner code.
14. There is an electric socket in the cabinet at the scene, which can be opened by the measuring ruler. The opening of the electric plug board is subject to the wall of the cabinet. If necessary, the electrical board can be mounted on the back panel without opening.
15. The solution for the top cabinet and beam cutting angle: first install the lower cabinet, saw the top cabinet board into the corresponding height, and place it on the side panel of the lower cabinet to take the spot ink as the quasi-saw angle.
16. The solution to the unevenness of the joint between the two closing plates and the top line. When making the first closing plate or top line and adding a small plate to the interface of the other board, expose 100-200mm, the purpose is to locate the board which is connected with it, and the small board can be fixed with 502 glue or screw.
17. If the drawer is loose and tight inside, the situation usually occurs when the nail back plate is not noticed, and the side plate is deformed. The hammer plate can be knocked out on the inner side of the side plate to restore the original shape.
18. When the gap between the door and the card door is large, there may be a deformation of the frame. The inner and outer door can be interchanged, and then the dust bar is added at the intersection of the two doors of the upper rail. If it is a full wooden door, The frame can be pressed down.
19. When the clothes on the upper cabinet exceeds two cabinets, the top and bottom plates are easy to be mixed: because the cabinets on the closet are made of different sizes, the top and bottom plates are not the same size, and the two sides are not the same width as the middle.
20. Wardrobe side panel deformation: mainly the wardrobe side panel seeing the light surface 2100mm below the fixed layer, the side panel is in the empty state, the door and the side panel will not be tight. In the design, put a solid layer below 2100mm of the light side panel.
Custom wardrobe installation notes:
Installation Note 1: Check the materials
After the wardrobe door with mirror door material is transported to the site, all materials should be inspected, meet the design requirements, check whether the size of the mirror door is correct, the diagonal deviation should not be greater than 1mm, and the door clamp, floor spring and handle specifications are correct. Whether the accessories are complete, after inspection, should be stored in a safe place, properly preserved, and covered for protection.
Installation Note 2: Punch positioning and installation of the door clamp
When installing the door clamp, use the door clamp to accurately mark the installation position line and the punching position on the mirror with the door and carefully remove the excess part with the pliers. Then drill the hole with the hand drill and the 18 mirror drill bit. Punching should be carried out gently and swayingly. It should be added with water. Do not press down when it is fast, so that it will naturally fall through, so that the perforated part has a mirror surface intact.
Installation Note 3: Install the door leaf
Remove the door clamp (F20) pre-installed on the door leaf and place the door leaf on the ground spring (use the plywood in the wardrobe with the mirror door and the mirror frame or other door frame to protect the mirror door and its door frame) Not damaged.), and on the same plane with two borders or mirrors, after the door leaf is placed, insert the F30?F40 upper door clamp shaft into the F20 upper door clamp sleeve, and reinstall the upper door clamp F20 on the mirrored door leaf. After the installation is completed, the adjustment is made. The switch is flexible. After the adjustment, the mirror rubber with the door clamp and the small wooden wedge with the mirror knife are cut flat than the upper end of the lower door clamp, and the glue should not be protruded outside the door clamp, and Clean and re-glue for modification.
Installation Note 4: Measuring distance and mounting handle
The handle between the handle and the mirror door is 120~150mm, and the installed door handle ensures symmetrical, vertical and firm.
Installation Note 5: Wardrobe Cleaning
After installation, use the mirror cleaning agent to clean the stain on the mirror door of the wardrobe to ensure the cleanliness of the wardrobe door.
Our boxes offer multifunctional and innovative solutions for storage. They are packable and stackable in a range of colours or in a transparent look so you can identify what you have stored in a glance
Plastic Storage Box,Household Organizer,Plastic Houseware,Plastic Storage Bins
SY INTERNATIONAL (CN) CO.,LTD , https://www.symanufactures.com