1. After the label is corrected, it can't be kept. Pressing the reservation will pop up a warning dialog box. After confirming, the software will be closed.
Cause: The user's correction directly caused the problem of correction on the label.
Solution: When correcting, correct the correction according to the correct correction method, double-click the content you want to correct, and correct it on the dialog box written in the original layout. It is not allowed to correct directly under the label. If corrected, the deformity will be restored.
2, barcode printer paper is not deformed, only half a sheet, after printing a red light (zebra rigid)
Cause: The printer parameter setting is faulty.
Treatment: Take Z4M as an example. Click Start menu -> Settings -> Printers -> Select Z4M -> Right-click -> Properties -> Printing Preferences -> documentOption -> DispenseMode -> Select TearOff to be OK.
3. When the printer is printing, all the indicators are shining, and the paper is not ready to be measured (zebra is not good).
Cause: The sensor is faulty.
Treatment: Wash the sensor's nominal dust or change the sensor.
4. The printer is not in place when printing small labels, and the printed content is always biased upwards or downwards. The label is too small, and the sensor is difficult to sense the paper.
Solution: The height of the malformed label should be greater than 10 to locate, otherwise the label should be stopped. When the label setting is stopped, the height of the label is set to be 5 mm shorter than the actual label, and then the offset of the label is stopped according to the detailed offset situation.
5, the font is clear when printing, the barcode is not clear Cause: too much barcode content, the density is too small.
Solution: Shrink the bar code content or increase the bar code density. For 200dpi and 300dpi rigid, the bar code density is more than 7mils, that is, the scale factor should be 2 or more, and the printed bar code is clear.
6. When printing labels, there are always some words that cannot be printed. The print head is dirty and the layout is wrong.
Treatment: Wash the print head; otherwise see if the words to be printed can be stacked together in the typesetting time, from the new layout.
7, the printer always shows no paper or no ribbon at the time of printing (TEC-572)
Cause: The paper runs out or the ribbon is wrong; sending the fault to manipulate the order.
Treatment: Review whether the paper or ribbon is accurate; adjust the parameters on the board, and then stop printing after using the printing software to accurately format the settings.
8. Printing is not clear when printing, and the ribbon is broken. (105Se/SL)
Cause: The printer has a ribbon rotation problem.
Treatment: The tension of the rigid ribbon on the shaft is too tight, and the tension of the ribbon of the printer ribbon is adjusted.
9, the new file can be malformed to print, but the old file can not be opened, helpless printing.
Cause: Collecting prints, permission problems.
Solution: The time of printing, whether the collection has ever opened the file, if it is turned over, you must first turn off the ability to open on another computer. Then collect the permission scores under the test.
10. The content is not printed completely when printing.
Cause: The printing software and driver version are too low.
Solution: Install a new version of the software and drivers.
11, the software can not stop typesetting.
Cause: The software is not installed or the computer scores.
Solution: From the new device software, if it is not possible, it is probably a virus in the computer, please kill the virus. No more, please reinstall the operating system.
12, shortly after the machine is turned on, the three lights will burn, but helpless to print.
Cause: The printer capacitor is broken.
Solution: Need to change the capacitor.
13, in the printing process, the printed content is not the same as the actual content.
Cause: The print driver is faulty.
Solution: Pick the exact printer driver sequence.
14. Black lines appear next to the process. (argox1000+)
Cause: The print head was not adjusted.
Solution: Condition the screws on the front of the print head.
15, the machine is not turned back (TEC-572)
Cause: Set up the problem.
Solution: Adjust the settings of the printer settings back to the rake, if not, it is probably the motherboard's emerging results, need to be repaired.
16, the printing often appears when the phenomenon of jumping paper: print settings.
Solution: When the paper size and spacing settings are accurate, change the BMP print pattern to PCX to stop printing.
17. In the process of rigid paper-feeding, the cause of the abnormal sound is recovered: the rigid image is not eliminated or the rigid tooth is bad.
Treatment: Eliminate dull images or change teeth*.
18, in the printing process, always showing the exhaustion of the ribbon: the rigid PCB-F or PCB-G bad treatment: change the PCB-F or change the PCB-G.
19. When the thermal printing is stopped, the front axle is constantly moving, and the ribbon is exhausted.
Cause: Difficult PCB-G is broken
5 Blade Razor,Fusion 5 Blades,Fusion Razor Blades,Five Blade Razor
GUANGZHOU WEIDI TECHNOLOGY CO., LTD , https://www.weidirazor.com